ultrasonic file · mani u-file · iso 15/.02 · 33 mm · 6
a stainless steel file your ultrasonic unit drives, not your fingers. iso 15 is the smallest of the four u-file sizes qed carries – white band, 0.15 mm tip.
this pack: 6 × mani u-file ultrasonic files, iso size 15, .02 taper, 33 mm, stainless steel, supplied non-sterile
made by mani, inc., japan – medical and dental instrument maker since 1956
| use | on an ultrasonic unit that takes a 0.8 mm shank (mani) |
| working part | 16 mm cutting flute on a 33 mm instrument |
| cross-section | square, sizes 10 to 40 (mani) |
| size and taper | iso 15 – 0.15 mm tip, .02 taper, white band |
› other sizes: u-file 20, 33 mm, u-file 25, 33 mm, u-file 35, 33 mm.
› same size by hand: d-finder 15, 25 mm – mani’s d-shaped hand file in the same iso size.
will it fit my ultrasonic unit?
mani’s requirement is a device that takes a 0.8 mm shank for sizes 10 to 40. the attachment and the power needed differ from one unit to the next, so mani say to follow the instructions from your unit’s maker.
what does mani say it is for?
mani list the intended use as root canal enlargement, and describe u-files as "very useful for cleaning or cutting root canal".
general points from the endodontic literature about ultrasonic files as a group – not mani’s instructions, and not specific to u-files.
› low power, short bursts. van der vyver, vorster and jonker (south african dental journal, 2020) work in the lower quarter of the unit’s power range and tap the foot control for one to two seconds rather than running it continuously.
› watch the heat. the same authors note that stainless steel tips can overheat with continuous activation, and that a temperature rise above 10°c risks the tissues around the root.
› for irrigant activation, keep it free. the file is usually held short of working length and left to oscillate without binding on the canal walls – van der sluis et al. (international endodontic journal, 2007) is the standard review.
| irrigants | chlorax 5.25% · endo-solution 17% edta |
| delivery | irriflex 30 ga · navitip 29 ga |
| hand files | mani d-finder 10, 25 mm · c-pilot 010, 25 mm |
| coronal seal | sdr flow+ refill universal |
ultrasonic file · iso 15 · .02 taper · 33 mm · 16 mm working part · 0.8 mm shank · stainless steel · non-sterile · 6 per pack · mani · ref 35637
ultrasonic file · mani u-file · iso 20/.02 · 33 mm · 6
same instrument, next size. a mani u-file with a 0.20 mm tip and the yellow iso band, so it is picked out of a tray at a glance.
this pack: 6 × mani u-file ultrasonic files, iso size 20, .02 taper, 33 mm, stainless steel, supplied non-sterile
made by mani, inc., japan – medical and dental instrument maker since 1956
| use | on an ultrasonic unit that takes a 0.8 mm shank (mani) |
| working part | 16 mm cutting flute on a 33 mm instrument |
| cross-section | square, sizes 10 to 40 (mani) |
| size and taper | iso 20 – 0.20 mm tip, .02 taper, yellow band |
› other sizes: u-file 15, 33 mm, u-file 25, 33 mm, u-file 35, 33 mm.
will it fit my ultrasonic unit?
mani’s requirement is a device that takes a 0.8 mm shank for sizes 10 to 40. the attachment and the power needed differ from one unit to the next, so mani say to follow the instructions from your unit’s maker.
what does mani say it is for?
mani list the intended use as root canal enlargement, and describe u-files as "very useful for cleaning or cutting root canal".
general points from the endodontic literature about ultrasonic files as a group – not mani’s instructions, and not specific to u-files.
› low power, short bursts. van der vyver, vorster and jonker (south african dental journal, 2020) work in the lower quarter of the unit’s power range and tap the foot control for one to two seconds rather than running it continuously.
› watch the heat. the same authors note that stainless steel tips can overheat with continuous activation, and that a temperature rise above 10°c risks the tissues around the root.
› for irrigant activation, keep it free. the file is usually held short of working length and left to oscillate without binding on the canal walls – van der sluis et al. (international endodontic journal, 2007) is the standard review.
| irrigants | chlorax 5.25% · endo-solution 17% edta |
| delivery | irriflex 30 ga · navitip 29 ga |
| hand files | mani d-finder 10, 25 mm · c-pilot 010, 25 mm |
| coronal seal | sdr flow+ refill universal |
ultrasonic file · iso 20 · .02 taper · 33 mm · 16 mm working part · 0.8 mm shank · stainless steel · non-sterile · 6 per pack · mani · ref 35643
ultrasonic file · mani u-file · iso 25/.02 · 33 mm · 6
the u-file on mani’s own product page is this one. a 0.25 mm tip, a .02 taper and the red iso band, for use on an ultrasonic unit.
this pack: 6 × mani u-file ultrasonic files, iso size 25, .02 taper, 33 mm, stainless steel, supplied non-sterile
made by mani, inc., japan – medical and dental instrument maker since 1956
| use | on an ultrasonic unit that takes a 0.8 mm shank (mani) |
| working part | 16 mm cutting flute on a 33 mm instrument |
| cross-section | square, sizes 10 to 40 (mani) |
| size and taper | iso 25 – 0.25 mm tip, .02 taper, red band |
› other sizes: u-file 15, 33 mm, u-file 20, 33 mm, u-file 35, 33 mm.
will it fit my ultrasonic unit?
mani’s requirement is a device that takes a 0.8 mm shank for sizes 10 to 40. the attachment and the power needed differ from one unit to the next, so mani say to follow the instructions from your unit’s maker.
what does mani say it is for?
mani list the intended use as root canal enlargement, and describe u-files as "very useful for cleaning or cutting root canal".
general points from the endodontic literature about ultrasonic files as a group – not mani’s instructions, and not specific to u-files.
› low power, short bursts. van der vyver, vorster and jonker (south african dental journal, 2020) work in the lower quarter of the unit’s power range and tap the foot control for one to two seconds rather than running it continuously.
› watch the heat. the same authors note that stainless steel tips can overheat with continuous activation, and that a temperature rise above 10°c risks the tissues around the root.
› for irrigant activation, keep it free. the file is usually held short of working length and left to oscillate without binding on the canal walls – van der sluis et al. (international endodontic journal, 2007) is the standard review.
| irrigants | chlorax 5.25% · endo-solution 17% edta |
| delivery | irriflex 30 ga · navitip 29 ga |
| hand files | mani d-finder 10, 25 mm · c-pilot 010, 25 mm |
| coronal seal | sdr flow+ refill universal |
ultrasonic file · iso 25 · .02 taper · 33 mm · 16 mm working part · 0.8 mm shank · stainless steel · non-sterile · 6 per pack · mani · ref 35650
therma-cut® burs · assorted · 25 mm
thermafil® and guttacore® carrierscuts by heat, no sprayfg turbinereusable, supplied non-sterilefour sizes in one pack
obturator seated – what takes the handle off? dentsply sirona’s instructions describe therma-cut® burs as devices “intended to cut the carrier obturators (e.g. thermafil® and guttacore®) at the canal entrance after placement”. the operative part ends in a non-cutting tip, made to cut the obturator by heating, and the bur runs in a turbine without water spray. this assortment holds all four sizes, iso 010 to 016.
this pack: 6 × therma-cut® fg burs, 25 mm, assorted: 1 × iso 010, 2 × 012, 2 × 014, 1 × 016 · stainless steel, non-sterile, reusable · ref a0050fg25ass · mfr code a005032590000
made by dentsply sirona
| sizes in the pack | iso 010 × 1, 012 × 2, 014 × 2, 016 × 1. a ring mark on the shank shows the size: dentsply sirona list ring mark 1 for 010, 2 for 012, 3 for 014 and 4 for 016 |
| fit and length | fg shank (iso 1797 type 3) for a contra-angle handpiece · 25 mm overall, 10 mm operative part · single-piece stainless steel |
| speed | dentsply sirona’s instructions: “a turbine without spray at a constant rotation speed of 300 000 rpm” |
| supplied non-sterile | reusable. dentsply sirona require processing before first use, following their general processing instructions for endodontic products at dentsplysirona.com/ifu |
› contraindications – dentsply sirona’s instructions list none known.
› rubber dam – recommended by dentsply sirona during the procedure, to avoid swallowing or inhalation of the bur.
› inspect before every use – dentsply sirona say to discard a bur that is bent, broken, corroded or has lost its marking, or that produces unusual vibration or noise. do not apply excessive pressure.
which obturators is it for?
dentsply sirona name thermafil® and guttacore® carrier obturators. we stock both: thermafil® posterior 20–40 assorted (20) · thermafil® anterior 45–100 assorted (20) · guttacore® 25 (6).
is it a cutting bur?
dentsply sirona describe the tip as non-cutting: it cuts the obturator by heating. their instructions specify a turbine without spray at 300,000 rpm, so follow the instructions supplied with the pack.
do i need it for the post space as well?
the thermafil® post space bur is a separate instrument for that job: size 050 · size 070.
therma-cut® burs, assorted · iso 010–016 · fg · 25 mm · stainless steel · non-cutting tip · 300,000 rpm, no spray · reusable, non-sterile · 6 burs · dentsply sirona · ref a0050fg25ass
thermafil® post space bur · 050 · 25 mm
post spaceplastic-carrier obturatorsfg turbinereusable, supplied non-sterile
thermafil® placed and a post to follow? dentsply sirona’s instructions say post-space burs “are used to prepare the post space removing thermafil® obturator (or another plastic core obturator)”, and that the device is intended for tooth preparation before post insertion. this is size 050: 25 mm long, 13 mm operative part, in a cassette of six.
this pack: 6 × post space burs, size 050, fg, 25 mm · stainless steel, non-sterile, reusable · ref a005131300500
made by dentsply sirona
| size | 050 · dentsply sirona’s instructions list it as iso 005, ring mark 1 |
| fit and length | fg shank (iso 1797 type 3) for a contra-angle handpiece · 25 mm overall, 13 mm operative part · single-piece stainless steel |
| speed | dentsply sirona’s instructions: “a turbine without spray at a constant rotation speed within the 200 000 – 350 000 rpm range” |
| supplied non-sterile | reusable. dentsply sirona require processing before first use, following their general processing instructions for endodontic products at dentsplysirona.com/ifu |
› contraindications – dentsply sirona’s instructions list none known.
› rubber dam – recommended by dentsply sirona during the procedure, to avoid swallowing or inhalation of the bur.
› inspect before every use – dentsply sirona say to discard a bur that is bent, broken, corroded or has lost its marking, or that produces unusual vibration or noise. do not apply excessive pressure.
what is the difference between size 050 and size 070?
only the size: the length and the operative part are the same, and the ring mark differs (1 for 050, 2 for 070). the other size is here: post space bur 070.
which obturators is it for?
dentsply sirona name thermafil® “or another plastic core obturator”. our thermafil® range: thermafil® posterior 20–40 assorted (20) · thermafil® anterior 45–100 assorted (20).
| carrier obturators | thermafil® posterior 20–40 assorted (20) · thermafil® anterior 45–100 assorted (20) · guttacore® 25 (6) |
| size verifiers | thermafil® verifiers 20–45 assorted, 25 mm (6) |
| cutting the carrier | therma-cut® burs, assorted 010–016, 25 mm · dentsply sirona |
| other post space size | thermafil® post space bur 070, 25 mm |
thermafil® post space bur · size 050 · fg · 25 mm · stainless steel · 200,000–350,000 rpm, no spray · reusable, non-sterile · 6 burs · dentsply sirona · ref a005131300500
thermafil® post space bur · 070 · 25 mm
post spaceplastic-carrier obturatorsfg turbinereusable, supplied non-sterile
thermafil® placed and a post to follow? dentsply sirona’s instructions say post-space burs “are used to prepare the post space removing thermafil® obturator (or another plastic core obturator)”, and that the device is intended for tooth preparation before post insertion. this is size 070: 25 mm long, 13 mm operative part, in a cassette of six.
this pack: 6 × post space burs, size 070, fg, 25 mm · stainless steel, non-sterile, reusable · ref a005131300700
made by dentsply sirona
| size | 070 · dentsply sirona’s instructions list it as iso 007, ring mark 2 |
| fit and length | fg shank (iso 1797 type 3) for a contra-angle handpiece · 25 mm overall, 13 mm operative part · single-piece stainless steel |
| speed | dentsply sirona’s instructions: “a turbine without spray at a constant rotation speed within the 200 000 – 350 000 rpm range” |
| supplied non-sterile | reusable. dentsply sirona require processing before first use, following their general processing instructions for endodontic products at dentsplysirona.com/ifu |
› contraindications – dentsply sirona’s instructions list none known.
› rubber dam – recommended by dentsply sirona during the procedure, to avoid swallowing or inhalation of the bur.
› inspect before every use – dentsply sirona say to discard a bur that is bent, broken, corroded or has lost its marking, or that produces unusual vibration or noise. do not apply excessive pressure.
what is the difference between size 050 and size 070?
only the size: the length and the operative part are the same, and the ring mark differs (1 for 050, 2 for 070). the other size is here: post space bur 050.
which obturators is it for?
dentsply sirona name thermafil® “or another plastic core obturator”. our thermafil® range: thermafil® posterior 20–40 assorted (20) · thermafil® anterior 45–100 assorted (20).
| carrier obturators | thermafil® posterior 20–40 assorted (20) · thermafil® anterior 45–100 assorted (20) · guttacore® 25 (6) |
| size verifiers | thermafil® verifiers 20–45 assorted, 25 mm (6) |
| cutting the carrier | therma-cut® burs, assorted 010–016, 25 mm · dentsply sirona |
| other post space size | thermafil® post space bur 050, 25 mm |
thermafil® post space bur · size 070 · fg · 25 mm · stainless steel · 200,000–350,000 rpm, no spray · reusable, non-sterile · 6 burs · dentsply sirona · ref a005131300700
round carbide bur · fg 010 · dentsply sirona
round carbidefriction gripsize 010pack of 6
maillefer’s carbide burs are cut from high-tenacity, micro-grain hard metal, and their brochure lists the round cavity bur (e 0123) for perforation, penetration, trepanation, excavation and retention.
this pack: 6 × round carbide burs, friction grip, size 010 · ref e012337101000
made by dentsply sirona (maillefer)
| shape | round (maillefer range e 0123) |
| material | tungsten carbide, cut from high-tenacity micro-grain hard metal (maillefer brochure) |
| shank | friction grip (fg) |
| size | 010 (iso) |
| speed | maillefer recommend 300,000 rpm for burs up to iso 010 (carbide brochure) |
| use | perforation, penetration, trepanation, excavation, retention (maillefer brochure, round cavity bur) |
what speed should size 010 run at?
maillefer’s carbide burs brochure recommends 300,000 rpm for burs up to iso 010, and 150,000 to 200,000 rpm for iso 012 and above. it is general guidance for their carbide burs, so check the pack label too.
how does it differ from size 014?
only the size. the size 014 pack is round carbide fg 014.
can the burs be reused?
maillefer’s endodontic access preparation directions say rotary cutting instruments are disinfected and sterilised before each use, and that it is safest to use their instruments only once. they are written for the access set these burs belong to rather than for this exact pack, so follow the pack label and your own decontamination procedure.
| same range | round carbide fg 010 (this page) · round carbide fg 014 · transmetal fg 012, 25 mm · transmetal fg 012, 19 mm · round diamond fg 016 |
| more access burs | diamendo no.1, 21 mm · zekrya extra-long tapered carbide bur, 23 mm · long neck carbide bur 010 |
round carbide bur fg · size 010 · friction grip · pack of 6 · dentsply sirona · ref e012337101000
round carbide bur · fg 014 · dentsply sirona
round carbidefriction gripsize 014pack of 6
maillefer’s carbide burs are cut from high-tenacity, micro-grain hard metal, and their brochure lists the round cavity bur (e 0123) for perforation, penetration, trepanation, excavation and retention.
this pack: 6 × round carbide burs, friction grip, size 014 · ref e012337101400
made by dentsply sirona (maillefer)
| shape | round (maillefer range e 0123) |
| material | tungsten carbide, cut from high-tenacity micro-grain hard metal (maillefer brochure) |
| shank | friction grip (fg) |
| size | 014 (iso) |
| speed | maillefer recommend 150,000 to 200,000 rpm for iso 012 and above (carbide brochure) |
| use | perforation, penetration, trepanation, excavation, retention (maillefer brochure, round cavity bur) |
what speed should size 014 run at?
maillefer’s carbide burs brochure recommends 150,000 to 200,000 rpm for iso 012 and above, and 300,000 rpm for burs up to iso 010. it is general guidance for their carbide burs, so check the pack label too.
how does it differ from size 010?
only the size. the size 010 pack is round carbide fg 010.
can the burs be reused?
maillefer’s endodontic access preparation directions say rotary cutting instruments are disinfected and sterilised before each use, and that it is safest to use their instruments only once. they are written for the access set these burs belong to rather than for this exact pack, so follow the pack label and your own decontamination procedure.
| same range | round carbide fg 010 · round carbide fg 014 (this page) · transmetal fg 012, 25 mm · transmetal fg 012, 19 mm · round diamond fg 016 |
| more access burs | diamendo no.1, 21 mm · zekrya extra-long tapered carbide bur, 23 mm · long neck carbide bur 010 |
round carbide bur fg · size 014 · friction grip · pack of 6 · dentsply sirona · ref e012337101400
ultrasonic file · mani u-file · iso 35/.02 · 33 mm · 6
iso 35 is the top of qed’s u-file range. a 0.35 mm tip, and still on the 0.8 mm shank that sizes 10 to 40 share.
this pack: 6 × mani u-file ultrasonic files, iso size 35, .02 taper, 33 mm, stainless steel, supplied non-sterile
made by mani, inc., japan – medical and dental instrument maker since 1956
| use | on an ultrasonic unit that takes a 0.8 mm shank (mani) |
| working part | 16 mm cutting flute on a 33 mm instrument |
| cross-section | square, sizes 10 to 40 (mani) |
| size and taper | iso 35 – 0.35 mm tip, .02 taper, green band |
› other sizes: u-file 15, 33 mm, u-file 20, 33 mm, u-file 25, 33 mm.
will it fit my ultrasonic unit?
mani’s requirement is a device that takes a 0.8 mm shank for sizes 10 to 40. the attachment and the power needed differ from one unit to the next, so mani say to follow the instructions from your unit’s maker.
what does mani say it is for?
mani list the intended use as root canal enlargement, and describe u-files as "very useful for cleaning or cutting root canal".
general points from the endodontic literature about ultrasonic files as a group – not mani’s instructions, and not specific to u-files.
› low power, short bursts. van der vyver, vorster and jonker (south african dental journal, 2020) work in the lower quarter of the unit’s power range and tap the foot control for one to two seconds rather than running it continuously.
› watch the heat. the same authors note that stainless steel tips can overheat with continuous activation, and that a temperature rise above 10°c risks the tissues around the root.
› for irrigant activation, keep it free. the file is usually held short of working length and left to oscillate without binding on the canal walls – van der sluis et al. (international endodontic journal, 2007) is the standard review.
| irrigants | chlorax 5.25% · endo-solution 17% edta |
| delivery | irriflex 30 ga · navitip 29 ga |
| hand files | mani d-finder 10, 25 mm · c-pilot 010, 25 mm |
| coronal seal | sdr flow+ refill universal |
ultrasonic file · iso 35 · .02 taper · 33 mm · 16 mm working part · 0.8 mm shank · stainless steel · non-sterile · 6 per pack · mani · ref manu3335
ss white endoguide® bur eg2 · 27 mm · pack of 5
de-roofingorifice enlargementcalcified canals
which endoguide® bur is eg2? ss white’s reference chart gives eg2 a 2.5 mm head on a 27 mm right angle shank, and lists it for: de-roofing pulp chamber; deep orifice enlargement and calcified canals. the endoguide® range is a set of carbide burs with a micro-diameter conical tip, made for root canal access and exploration.
this pack: ss white endoguide® bur eg2, carbide, right angle shank, 27 mm (pack of 5)
| type | carbide micro endodontic bur (ss white) |
| head length | 2.5 mm |
| tip diameter | 0.33 mm |
| back diameter | 1.07 mm |
| overall length | 27 mm |
| shank | right angle, surgical length (ss white code slra) – for slow-speed right-angle handpieces |
| pack | pack of 5 |
| ss white lists it for | • de-roofing pulp chamber • deep orifice enlargement and calcified canals |
› what they are. ss white describe endoguide® as an innovative set of carbide burs designed for non-surgical endodontic procedures, developed in conjunction with dr david clark dds and dr john a khademi dds ms.
› what they are designed for. root canal access and exploration; tactile and magnification-enhanced endodontics; use by endodontists and general dentists.
› design aims they list. funnel-shaped access for file introduction, access to calcified and hidden canals, conserving peri-cervical dentin, and reduced dependence on ultrasonic tips.
› tip and shape. against conventional access burs, ss white describe the micro-diameter tip as leading to more conservative access and the conical shape to more efficient access. they describe the tip as a self-centring guide, and the straight-line pathway as reducing the risk of gouging and perforation when used with an incisal access technique for canal entry.
“this is an ideal bur series for magnification-driven endodontics.”
eric herbranson, bs, dds, ms – quoted in ss white’s endoguide® brochure
the eight burs in ss white’s chart, with the figures ss white print for each:
| eg1a | endoguide® eg1a (5) 27 mm · friction grip · head 2.5 mm · tip 0.33 mm – initial access in non-restored anterior and bicuspid teeth |
| eg1 | endoguide® eg1 (5) 27 mm · right angle · head 3.5 mm · tip 0.28 mm – deep troughing; deeper orifice enlargement and calcified canals |
| eg2 | this page. 27 mm · right angle · head 2.5 mm · tip 0.33 mm – de-roofing pulp chamber; deep orifice enlargement and calcified canals |
| eg3 | endoguide® eg3 (5) 27 mm · friction grip · head 1.5 mm · tip 0.28 mm – initial access for small incisors; troughing and navigating calcified canals |
| eg4 | endoguide® eg4 (5) 29 mm · friction grip · head 3.5 mm · tip 0.28 mm – deep troughing; navigating super ovoid and calcified canals |
| eg5 | endoguide® eg5 (5) 34 mm · right angle · head 1.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg6 | endoguide® eg6 (5) 34 mm · right angle · head 2.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg7 | endoguide® eg7 (5) 34 mm · right angle · head 1.5 mm · tip 0.33 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
ss white include eg2 in the endoguide® molar kit and endoguide® anterior/bicuspid kit. ss white add a note to the kit listings: initial access and de-roofing in molars should be performed with either the great white® #2 bur or the great white® z diamonds supplied in the endoguide® anterior/bicuspid kit, order number 18052.
| kits | endoguide® molar kit · endoguide® anterior/bicuspid kit |
| hand file | vdw c-pilot™ 08, 25 mm · c-pilot™ 10, 25 mm |
| irrigants | chlorax 5.25% sodium hypochlorite · chlorax 2% |
endoguide® bur eg2 · right angle shank (slra) · 27 mm · head 2.5 mm · tip 0.33 mm · back 1.07 mm · carbide · pack of 5 · made by ss white burs, inc., lakewood, new jersey, usa · mfr code 14779 · ref ssw-14779
ss white endoguide® bur eg1 · 27 mm · pack of 5
deep troughingorifice enlargementcalcified canals
which endoguide® bur is eg1? ss white’s reference chart gives eg1 a 3.5 mm head on a 27 mm right angle shank, and lists it for: deep troughing; deeper orifice enlargement and calcified canals. the endoguide® range is a set of carbide burs with a micro-diameter conical tip, made for root canal access and exploration.
this pack: ss white endoguide® bur eg1, carbide, right angle shank, 27 mm (pack of 5)
| type | carbide micro endodontic bur (ss white) |
| head length | 3.5 mm |
| tip diameter | 0.28 mm |
| back diameter | 0.71 mm |
| overall length | 27 mm |
| shank | right angle, surgical length (ss white code slra) – for slow-speed right-angle handpieces |
| pack | pack of 5 |
| ss white lists it for | • deep troughing • deeper orifice enlargement and calcified canals |
› what they are. ss white describe endoguide® as an innovative set of carbide burs designed for non-surgical endodontic procedures, developed in conjunction with dr david clark dds and dr john a khademi dds ms.
› what they are designed for. root canal access and exploration; tactile and magnification-enhanced endodontics; use by endodontists and general dentists.
› design aims they list. funnel-shaped access for file introduction, access to calcified and hidden canals, conserving peri-cervical dentin, and reduced dependence on ultrasonic tips.
› tip and shape. against conventional access burs, ss white describe the micro-diameter tip as leading to more conservative access and the conical shape to more efficient access. they describe the tip as a self-centring guide, and the straight-line pathway as reducing the risk of gouging and perforation when used with an incisal access technique for canal entry.
“this is an ideal bur series for magnification-driven endodontics.”
eric herbranson, bs, dds, ms – quoted in ss white’s endoguide® brochure
the eight burs in ss white’s chart, with the figures ss white print for each:
| eg1a | endoguide® eg1a (5) 27 mm · friction grip · head 2.5 mm · tip 0.33 mm – initial access in non-restored anterior and bicuspid teeth |
| eg1 | this page. 27 mm · right angle · head 3.5 mm · tip 0.28 mm – deep troughing; deeper orifice enlargement and calcified canals |
| eg2 | endoguide® eg2 (5) 27 mm · right angle · head 2.5 mm · tip 0.33 mm – de-roofing pulp chamber; deep orifice enlargement and calcified canals |
| eg3 | endoguide® eg3 (5) 27 mm · friction grip · head 1.5 mm · tip 0.28 mm – initial access for small incisors; troughing and navigating calcified canals |
| eg4 | endoguide® eg4 (5) 29 mm · friction grip · head 3.5 mm · tip 0.28 mm – deep troughing; navigating super ovoid and calcified canals |
| eg5 | endoguide® eg5 (5) 34 mm · right angle · head 1.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg6 | endoguide® eg6 (5) 34 mm · right angle · head 2.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg7 | endoguide® eg7 (5) 34 mm · right angle · head 1.5 mm · tip 0.33 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
ss white include eg1 in the endoguide® molar kit and endoguide® anterior/bicuspid kit.
| kits | endoguide® molar kit · endoguide® anterior/bicuspid kit |
| hand file | vdw c-pilot™ 08, 25 mm · c-pilot™ 10, 25 mm |
| irrigants | chlorax 5.25% sodium hypochlorite · chlorax 2% |
endoguide® bur eg1 · right angle shank (slra) · 27 mm · head 3.5 mm · tip 0.28 mm · back 0.71 mm · carbide · pack of 5 · made by ss white burs, inc., lakewood, new jersey, usa · mfr code 14780 · ref ssw-14780
ss white endoguide® bur eg7 · 34 mm · pack of 5
deep troughingseparated instrumentsdeeply calcified canals
which endoguide® bur is eg7? ss white’s reference chart gives eg7 a 1.5 mm head on a 34 mm right angle shank, and lists it for: deep troughing; retrieving separated instruments; navigating deeply calcified canals. the endoguide® range is a set of carbide burs with a micro-diameter conical tip, made for root canal access and exploration.
this pack: ss white endoguide® bur eg7, carbide, right angle shank, 34 mm (pack of 5)
| type | carbide micro endodontic bur (ss white) |
| head length | 1.5 mm |
| tip diameter | 0.33 mm |
| back diameter | 1.07 mm |
| overall length | 34 mm |
| shank | right angle, extra long (ss white code xlra) – for slow-speed right-angle handpieces |
| pack | pack of 5 |
| ss white lists it for | • deep troughing • retrieving separated instruments • navigating deeply calcified canals |
› what they are. ss white describe endoguide® as an innovative set of carbide burs designed for non-surgical endodontic procedures, developed in conjunction with dr david clark dds and dr john a khademi dds ms.
› what they are designed for. root canal access and exploration; tactile and magnification-enhanced endodontics; use by endodontists and general dentists.
› design aims they list. funnel-shaped access for file introduction, access to calcified and hidden canals, conserving peri-cervical dentin, and reduced dependence on ultrasonic tips.
› tip and shape. against conventional access burs, ss white describe the micro-diameter tip as leading to more conservative access and the conical shape to more efficient access. they describe the tip as a self-centring guide, and the straight-line pathway as reducing the risk of gouging and perforation when used with an incisal access technique for canal entry.
“this is an ideal bur series for magnification-driven endodontics.”
eric herbranson, bs, dds, ms – quoted in ss white’s endoguide® brochure
the eight burs in ss white’s chart, with the figures ss white print for each:
| eg1a | endoguide® eg1a (5) 27 mm · friction grip · head 2.5 mm · tip 0.33 mm – initial access in non-restored anterior and bicuspid teeth |
| eg1 | endoguide® eg1 (5) 27 mm · right angle · head 3.5 mm · tip 0.28 mm – deep troughing; deeper orifice enlargement and calcified canals |
| eg2 | endoguide® eg2 (5) 27 mm · right angle · head 2.5 mm · tip 0.33 mm – de-roofing pulp chamber; deep orifice enlargement and calcified canals |
| eg3 | endoguide® eg3 (5) 27 mm · friction grip · head 1.5 mm · tip 0.28 mm – initial access for small incisors; troughing and navigating calcified canals |
| eg4 | endoguide® eg4 (5) 29 mm · friction grip · head 3.5 mm · tip 0.28 mm – deep troughing; navigating super ovoid and calcified canals |
| eg5 | endoguide® eg5 (5) 34 mm · right angle · head 1.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg6 | endoguide® eg6 (5) 34 mm · right angle · head 2.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg7 | this page. 34 mm · right angle · head 1.5 mm · tip 0.33 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
ss white include eg7 in the endoguide® molar kit.
| kits | endoguide® molar kit · endoguide® anterior/bicuspid kit |
| hand file | vdw c-pilot™ 08, 25 mm · c-pilot™ 10, 25 mm |
| irrigants | chlorax 5.25% sodium hypochlorite · chlorax 2% |
endoguide® bur eg7 · right angle shank (xlra) · 34 mm · head 1.5 mm · tip 0.33 mm · back 1.07 mm · carbide · pack of 5 · made by ss white burs, inc., lakewood, new jersey, usa · mfr code 14786 · ref ssw-14786
ss white endoguide® bur eg5 · 34 mm · pack of 5
deep troughingseparated instrumentsdeeply calcified canals
which endoguide® bur is eg5? ss white’s reference chart gives eg5 a 1.5 mm head on a 34 mm right angle shank, and lists it for: deep troughing; retrieving separated instruments; navigating deeply calcified canals. the endoguide® range is a set of carbide burs with a micro-diameter conical tip, made for root canal access and exploration.
this pack: ss white endoguide® bur eg5, carbide, right angle shank, 34 mm (pack of 5)
| type | carbide micro endodontic bur (ss white) |
| head length | 1.5 mm |
| tip diameter | 0.28 mm |
| back diameter | 0.71 mm |
| overall length | 34 mm |
| shank | right angle, extra long (ss white code xlra) – for slow-speed right-angle handpieces |
| pack | pack of 5 |
| ss white lists it for | • deep troughing • retrieving separated instruments • navigating deeply calcified canals |
› what they are. ss white describe endoguide® as an innovative set of carbide burs designed for non-surgical endodontic procedures, developed in conjunction with dr david clark dds and dr john a khademi dds ms.
› what they are designed for. root canal access and exploration; tactile and magnification-enhanced endodontics; use by endodontists and general dentists.
› design aims they list. funnel-shaped access for file introduction, access to calcified and hidden canals, conserving peri-cervical dentin, and reduced dependence on ultrasonic tips.
› tip and shape. against conventional access burs, ss white describe the micro-diameter tip as leading to more conservative access and the conical shape to more efficient access. they describe the tip as a self-centring guide, and the straight-line pathway as reducing the risk of gouging and perforation when used with an incisal access technique for canal entry.
“this is an ideal bur series for magnification-driven endodontics.”
eric herbranson, bs, dds, ms – quoted in ss white’s endoguide® brochure
the eight burs in ss white’s chart, with the figures ss white print for each:
| eg1a | endoguide® eg1a (5) 27 mm · friction grip · head 2.5 mm · tip 0.33 mm – initial access in non-restored anterior and bicuspid teeth |
| eg1 | endoguide® eg1 (5) 27 mm · right angle · head 3.5 mm · tip 0.28 mm – deep troughing; deeper orifice enlargement and calcified canals |
| eg2 | endoguide® eg2 (5) 27 mm · right angle · head 2.5 mm · tip 0.33 mm – de-roofing pulp chamber; deep orifice enlargement and calcified canals |
| eg3 | endoguide® eg3 (5) 27 mm · friction grip · head 1.5 mm · tip 0.28 mm – initial access for small incisors; troughing and navigating calcified canals |
| eg4 | endoguide® eg4 (5) 29 mm · friction grip · head 3.5 mm · tip 0.28 mm – deep troughing; navigating super ovoid and calcified canals |
| eg5 | this page. 34 mm · right angle · head 1.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg6 | endoguide® eg6 (5) 34 mm · right angle · head 2.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg7 | endoguide® eg7 (5) 34 mm · right angle · head 1.5 mm · tip 0.33 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
ss white include eg5 in the endoguide® molar kit.
| kits | endoguide® molar kit · endoguide® anterior/bicuspid kit |
| hand file | vdw c-pilot™ 08, 25 mm · c-pilot™ 10, 25 mm |
| irrigants | chlorax 5.25% sodium hypochlorite · chlorax 2% |
endoguide® bur eg5 · right angle shank (xlra) · 34 mm · head 1.5 mm · tip 0.28 mm · back 0.71 mm · carbide · pack of 5 · made by ss white burs, inc., lakewood, new jersey, usa · mfr code 14794 · ref ssw-14794
ss white endoguide® bur eg6 · 34 mm · pack of 5
deep troughingseparated instrumentsdeeply calcified canals
which endoguide® bur is eg6? ss white’s reference chart gives eg6 a 2.5 mm head on a 34 mm right angle shank, and lists it for: deep troughing; retrieving separated instruments; navigating deeply calcified canals. the endoguide® range is a set of carbide burs with a micro-diameter conical tip, made for root canal access and exploration.
this pack: ss white endoguide® bur eg6, carbide, right angle shank, 34 mm (pack of 5)
| type | carbide micro endodontic bur (ss white) |
| head length | 2.5 mm |
| tip diameter | 0.28 mm |
| back diameter | 0.71 mm |
| overall length | 34 mm |
| shank | right angle, extra long (ss white code xlra) – for slow-speed right-angle handpieces |
| pack | pack of 5 |
| ss white lists it for | • deep troughing • retrieving separated instruments • navigating deeply calcified canals |
› what they are. ss white describe endoguide® as an innovative set of carbide burs designed for non-surgical endodontic procedures, developed in conjunction with dr david clark dds and dr john a khademi dds ms.
› what they are designed for. root canal access and exploration; tactile and magnification-enhanced endodontics; use by endodontists and general dentists.
› design aims they list. funnel-shaped access for file introduction, access to calcified and hidden canals, conserving peri-cervical dentin, and reduced dependence on ultrasonic tips.
› tip and shape. against conventional access burs, ss white describe the micro-diameter tip as leading to more conservative access and the conical shape to more efficient access. they describe the tip as a self-centring guide, and the straight-line pathway as reducing the risk of gouging and perforation when used with an incisal access technique for canal entry.
“this is an ideal bur series for magnification-driven endodontics.”
eric herbranson, bs, dds, ms – quoted in ss white’s endoguide® brochure
the eight burs in ss white’s chart, with the figures ss white print for each:
| eg1a | endoguide® eg1a (5) 27 mm · friction grip · head 2.5 mm · tip 0.33 mm – initial access in non-restored anterior and bicuspid teeth |
| eg1 | endoguide® eg1 (5) 27 mm · right angle · head 3.5 mm · tip 0.28 mm – deep troughing; deeper orifice enlargement and calcified canals |
| eg2 | endoguide® eg2 (5) 27 mm · right angle · head 2.5 mm · tip 0.33 mm – de-roofing pulp chamber; deep orifice enlargement and calcified canals |
| eg3 | endoguide® eg3 (5) 27 mm · friction grip · head 1.5 mm · tip 0.28 mm – initial access for small incisors; troughing and navigating calcified canals |
| eg4 | endoguide® eg4 (5) 29 mm · friction grip · head 3.5 mm · tip 0.28 mm – deep troughing; navigating super ovoid and calcified canals |
| eg5 | endoguide® eg5 (5) 34 mm · right angle · head 1.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg6 | this page. 34 mm · right angle · head 2.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg7 | endoguide® eg7 (5) 34 mm · right angle · head 1.5 mm · tip 0.33 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
ss white include eg6 in the endoguide® molar kit.
| kits | endoguide® molar kit · endoguide® anterior/bicuspid kit |
| hand file | vdw c-pilot™ 08, 25 mm · c-pilot™ 10, 25 mm |
| irrigants | chlorax 5.25% sodium hypochlorite · chlorax 2% |
endoguide® bur eg6 · right angle shank (xlra) · 34 mm · head 2.5 mm · tip 0.28 mm · back 0.71 mm · carbide · pack of 5 · made by ss white burs, inc., lakewood, new jersey, usa · mfr code 14795 · ref ssw-14795
ss white endoguide® bur eg3 · 27 mm · pack of 5
small incisorstroughingcalcified canals
which endoguide® bur is eg3? ss white’s reference chart gives eg3 a 1.5 mm head on a 27 mm friction grip shank, and lists it for: initial access for small incisors; troughing and navigating calcified canals. the endoguide® range is a set of carbide burs with a micro-diameter conical tip, made for root canal access and exploration.
this pack: ss white endoguide® bur eg3, carbide, friction grip shank, 27 mm (pack of 5)
| type | carbide micro endodontic bur (ss white) |
| head length | 1.5 mm |
| tip diameter | 0.28 mm |
| back diameter | 0.71 mm |
| overall length | 27 mm |
| shank | friction grip, surgical length (ss white code slfg) – for friction grip high-speed handpieces |
| pack | pack of 5 |
| ss white lists it for | • initial access for small incisors • troughing and navigating calcified canals |
› what they are. ss white describe endoguide® as an innovative set of carbide burs designed for non-surgical endodontic procedures, developed in conjunction with dr david clark dds and dr john a khademi dds ms.
› what they are designed for. root canal access and exploration; tactile and magnification-enhanced endodontics; use by endodontists and general dentists.
› design aims they list. funnel-shaped access for file introduction, access to calcified and hidden canals, conserving peri-cervical dentin, and reduced dependence on ultrasonic tips.
› tip and shape. against conventional access burs, ss white describe the micro-diameter tip as leading to more conservative access and the conical shape to more efficient access. they describe the tip as a self-centring guide, and the straight-line pathway as reducing the risk of gouging and perforation when used with an incisal access technique for canal entry.
“this is an ideal bur series for magnification-driven endodontics.”
eric herbranson, bs, dds, ms – quoted in ss white’s endoguide® brochure
the eight burs in ss white’s chart, with the figures ss white print for each:
| eg1a | endoguide® eg1a (5) 27 mm · friction grip · head 2.5 mm · tip 0.33 mm – initial access in non-restored anterior and bicuspid teeth |
| eg1 | endoguide® eg1 (5) 27 mm · right angle · head 3.5 mm · tip 0.28 mm – deep troughing; deeper orifice enlargement and calcified canals |
| eg2 | endoguide® eg2 (5) 27 mm · right angle · head 2.5 mm · tip 0.33 mm – de-roofing pulp chamber; deep orifice enlargement and calcified canals |
| eg3 | this page. 27 mm · friction grip · head 1.5 mm · tip 0.28 mm – initial access for small incisors; troughing and navigating calcified canals |
| eg4 | endoguide® eg4 (5) 29 mm · friction grip · head 3.5 mm · tip 0.28 mm – deep troughing; navigating super ovoid and calcified canals |
| eg5 | endoguide® eg5 (5) 34 mm · right angle · head 1.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg6 | endoguide® eg6 (5) 34 mm · right angle · head 2.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg7 | endoguide® eg7 (5) 34 mm · right angle · head 1.5 mm · tip 0.33 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
ss white include eg3 in the endoguide® molar kit and endoguide® anterior/bicuspid kit.
| kits | endoguide® molar kit · endoguide® anterior/bicuspid kit |
| hand file | vdw c-pilot™ 08, 25 mm · c-pilot™ 10, 25 mm |
| irrigants | chlorax 5.25% sodium hypochlorite · chlorax 2% |
endoguide® bur eg3 · friction grip shank (slfg) · 27 mm · head 1.5 mm · tip 0.28 mm · back 0.71 mm · carbide · pack of 5 · made by ss white burs, inc., lakewood, new jersey, usa · mfr code 15023 · ref ssw-15023
ss white endoguide® bur eg4 · 29 mm · pack of 5
deep troughingsuper ovoid canalscalcified canals
which endoguide® bur is eg4? ss white’s reference chart gives eg4 a 3.5 mm head on a 29 mm friction grip shank, and lists it for: deep troughing; navigating super ovoid and calcified canals. the endoguide® range is a set of carbide burs with a micro-diameter conical tip, made for root canal access and exploration.
this pack: ss white endoguide® bur eg4, carbide, friction grip shank, 29 mm (pack of 5)
| type | carbide micro endodontic bur (ss white) |
| head length | 3.5 mm |
| tip diameter | 0.28 mm |
| back diameter | 0.71 mm |
| overall length | 29 mm |
| shank | friction grip, surgical length (ss white code slfg) – for friction grip high-speed handpieces |
| pack | pack of 5 |
| ss white lists it for | • deep troughing • navigating super ovoid and calcified canals |
› what they are. ss white describe endoguide® as an innovative set of carbide burs designed for non-surgical endodontic procedures, developed in conjunction with dr david clark dds and dr john a khademi dds ms.
› what they are designed for. root canal access and exploration; tactile and magnification-enhanced endodontics; use by endodontists and general dentists.
› design aims they list. funnel-shaped access for file introduction, access to calcified and hidden canals, conserving peri-cervical dentin, and reduced dependence on ultrasonic tips.
› tip and shape. against conventional access burs, ss white describe the micro-diameter tip as leading to more conservative access and the conical shape to more efficient access. they describe the tip as a self-centring guide, and the straight-line pathway as reducing the risk of gouging and perforation when used with an incisal access technique for canal entry.
“this is an ideal bur series for magnification-driven endodontics.”
eric herbranson, bs, dds, ms – quoted in ss white’s endoguide® brochure
the eight burs in ss white’s chart, with the figures ss white print for each:
| eg1a | endoguide® eg1a (5) 27 mm · friction grip · head 2.5 mm · tip 0.33 mm – initial access in non-restored anterior and bicuspid teeth |
| eg1 | endoguide® eg1 (5) 27 mm · right angle · head 3.5 mm · tip 0.28 mm – deep troughing; deeper orifice enlargement and calcified canals |
| eg2 | endoguide® eg2 (5) 27 mm · right angle · head 2.5 mm · tip 0.33 mm – de-roofing pulp chamber; deep orifice enlargement and calcified canals |
| eg3 | endoguide® eg3 (5) 27 mm · friction grip · head 1.5 mm · tip 0.28 mm – initial access for small incisors; troughing and navigating calcified canals |
| eg4 | this page. 29 mm · friction grip · head 3.5 mm · tip 0.28 mm – deep troughing; navigating super ovoid and calcified canals |
| eg5 | endoguide® eg5 (5) 34 mm · right angle · head 1.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg6 | endoguide® eg6 (5) 34 mm · right angle · head 2.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg7 | endoguide® eg7 (5) 34 mm · right angle · head 1.5 mm · tip 0.33 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
ss white include eg4 in the endoguide® molar kit.
| kits | endoguide® molar kit · endoguide® anterior/bicuspid kit |
| hand file | vdw c-pilot™ 08, 25 mm · c-pilot™ 10, 25 mm |
| irrigants | chlorax 5.25% sodium hypochlorite · chlorax 2% |
endoguide® bur eg4 · friction grip shank (slfg) · 29 mm · head 3.5 mm · tip 0.28 mm · back 0.71 mm · carbide · pack of 5 · made by ss white burs, inc., lakewood, new jersey, usa · mfr code 15029 · ref ssw-15029
ss white endoguide® bur eg1a · 27 mm · pack of 5
anterior teethbicuspid teethinitial access
which endoguide® bur is eg1a? ss white’s reference chart gives eg1a a 2.5 mm head on a 27 mm friction grip shank, and lists it for: initial access in non-restored anterior and bicuspid teeth. the endoguide® range is a set of carbide burs with a micro-diameter conical tip, made for root canal access and exploration.
this pack: ss white endoguide® bur eg1a, carbide, friction grip shank, 27 mm (pack of 5)
| type | carbide micro endodontic bur (ss white) |
| head length | 2.5 mm |
| tip diameter | 0.33 mm |
| back diameter | 1.07 mm |
| overall length | 27 mm |
| shank | friction grip, surgical length (ss white code slfg) – for friction grip high-speed handpieces |
| pack | pack of 5 |
| ss white lists it for | • initial access in non-restored anterior and bicuspid teeth |
› what they are. ss white describe endoguide® as an innovative set of carbide burs designed for non-surgical endodontic procedures, developed in conjunction with dr david clark dds and dr john a khademi dds ms.
› what they are designed for. root canal access and exploration; tactile and magnification-enhanced endodontics; use by endodontists and general dentists.
› design aims they list. funnel-shaped access for file introduction, access to calcified and hidden canals, conserving peri-cervical dentin, and reduced dependence on ultrasonic tips.
› tip and shape. against conventional access burs, ss white describe the micro-diameter tip as leading to more conservative access and the conical shape to more efficient access. they describe the tip as a self-centring guide, and the straight-line pathway as reducing the risk of gouging and perforation when used with an incisal access technique for canal entry.
“this is an ideal bur series for magnification-driven endodontics.”
eric herbranson, bs, dds, ms – quoted in ss white’s endoguide® brochure
the eight burs in ss white’s chart, with the figures ss white print for each:
| eg1a | this page. 27 mm · friction grip · head 2.5 mm · tip 0.33 mm – initial access in non-restored anterior and bicuspid teeth |
| eg1 | endoguide® eg1 (5) 27 mm · right angle · head 3.5 mm · tip 0.28 mm – deep troughing; deeper orifice enlargement and calcified canals |
| eg2 | endoguide® eg2 (5) 27 mm · right angle · head 2.5 mm · tip 0.33 mm – de-roofing pulp chamber; deep orifice enlargement and calcified canals |
| eg3 | endoguide® eg3 (5) 27 mm · friction grip · head 1.5 mm · tip 0.28 mm – initial access for small incisors; troughing and navigating calcified canals |
| eg4 | endoguide® eg4 (5) 29 mm · friction grip · head 3.5 mm · tip 0.28 mm – deep troughing; navigating super ovoid and calcified canals |
| eg5 | endoguide® eg5 (5) 34 mm · right angle · head 1.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg6 | endoguide® eg6 (5) 34 mm · right angle · head 2.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg7 | endoguide® eg7 (5) 34 mm · right angle · head 1.5 mm · tip 0.33 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
ss white include eg1a in the endoguide® anterior/bicuspid kit.
| kits | endoguide® molar kit · endoguide® anterior/bicuspid kit |
| hand file | vdw c-pilot™ 08, 25 mm · c-pilot™ 10, 25 mm |
| irrigants | chlorax 5.25% sodium hypochlorite · chlorax 2% |
endoguide® bur eg1a · friction grip shank (slfg) · 27 mm · head 2.5 mm · tip 0.33 mm · back 1.07 mm · carbide · pack of 5 · made by ss white burs, inc., lakewood, new jersey, usa · mfr code 15066 · ref ssw-15066
ss white endoguide® molar kit · 7 burs
molar explorationhidden canalstroughing
which burs come in the endoguide® molar kit? seven: eg1 to eg7. ss white say they are designed to increase visibility and control during endodontic exploration in molars, when locating hidden canals, navigating deeply calcified canals and troughing between canals.
this kit: ss white endoguide® molar kit, order number 18051 – seven carbide burs, eg1 to eg7, in a stand
one of each, as photographed in the stand. the figures are ss white’s own chart entries for each bur:
| eg1 | 27 mm · right angle · head 3.5 mm · tip 0.28 mm – deep troughing; deeper orifice enlargement and calcified canals |
| eg2 | 27 mm · right angle · head 2.5 mm · tip 0.33 mm – de-roofing pulp chamber; deep orifice enlargement and calcified canals |
| eg3 | 27 mm · friction grip · head 1.5 mm · tip 0.28 mm – initial access for small incisors; troughing and navigating calcified canals |
| eg4 | 29 mm · friction grip · head 3.5 mm · tip 0.28 mm – deep troughing; navigating super ovoid and calcified canals |
| eg5 | 34 mm · right angle · head 1.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg6 | 34 mm · right angle · head 2.5 mm · tip 0.28 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
| eg7 | 34 mm · right angle · head 1.5 mm · tip 0.33 mm – deep troughing; retrieving separated instruments; navigating deeply calcified canals |
› what they are. ss white describe endoguide® as an innovative set of carbide burs designed for non-surgical endodontic procedures, developed in conjunction with dr david clark dds and dr john a khademi dds ms.
› what they are designed for. root canal access and exploration; tactile and magnification-enhanced endodontics; use by endodontists and general dentists.
› design aims they list. funnel-shaped access for file introduction, access to calcified and hidden canals, conserving peri-cervical dentin, and reduced dependence on ultrasonic tips.
› tip and shape. against conventional access burs, ss white describe the micro-diameter tip as leading to more conservative access and the conical shape to more efficient access. they describe the tip as a self-centring guide, and the straight-line pathway as reducing the risk of gouging and perforation when used with an incisal access technique for canal entry.
“this is an ideal bur series for magnification-driven endodontics.”
eric herbranson, bs, dds, ms – quoted in ss white’s endoguide® brochure
ss white add a note to the kit listings: initial access and de-roofing in molars should be performed with either the great white® #2 bur or the great white® z diamonds supplied in the endoguide® anterior/bicuspid kit, order number 18052.
| single burs (5) | eg1 · eg2 · eg3 · eg4 · eg5 · eg6 · eg7 |
| kits | endoguide® anterior/bicuspid kit |
| hand file | vdw c-pilot™ 08, 25 mm · c-pilot™ 10, 25 mm |
| irrigants | chlorax 5.25% sodium hypochlorite · chlorax 2% |
endoguide® molar kit · order number 18051 · seven carbide burs eg1 to eg7 · made by ss white burs, inc., lakewood, new jersey, usa · ref ssw-18051
ss white endoguide® anterior/bicuspid kit · 7 burs
metal, porcelain, zirconiaanterior and bicuspidaccess and exploration
what is in the endoguide® anterior/bicuspid kit? ss white say it contains all the instrumentation to create endodontic access through metal, porcelain and zirconia: a great white® #2 metal-cutting bur, great white® z diamonds and four endoguide® burs, eg1a, eg1, eg2 and eg3, for locating and accessing single root canals in anterior and bicuspid teeth.
this kit: ss white endoguide® anterior/bicuspid kit, order number 18052 – four endoguide® burs and three great white® burs, in a stand
one of each, as photographed in the stand. the figures are ss white’s own chart entries:
| eg1a | 27 mm · friction grip · head 2.5 mm · tip 0.33 mm – initial access in non-restored anterior and bicuspid teeth |
| eg1 | 27 mm · right angle · head 3.5 mm · tip 0.28 mm – deep troughing; deeper orifice enlargement and calcified canals |
| eg2 | 27 mm · right angle · head 2.5 mm · tip 0.33 mm – de-roofing pulp chamber; deep orifice enlargement and calcified canals |
| eg3 | 27 mm · friction grip · head 1.5 mm · tip 0.28 mm – initial access for small incisors; troughing and navigating calcified canals |
| gw2 | great white® #2, friction grip, 19 mm, head 4.0 mm, back 1.19 mm – metal crown access or removal; amalgam restoration and decay removal; molar initial access and de-roofing |
| gwz 856-018 | great white® z diamond, round end cone, friction grip, 22 mm, head 8.0 mm, tip 1.10 mm, back 2.2 mm – ceramic/zirconia crown removal; molar initial access and de-roofing |
| gwz 801-018 | great white® z diamond, round, friction grip, 19 mm, head 1.8 mm, back 1.90 mm – initial access through ceramic/zirconia crowns; molar initial access and de-roofing |
› what they are. ss white describe endoguide® as an innovative set of carbide burs designed for non-surgical endodontic procedures, developed in conjunction with dr david clark dds and dr john a khademi dds ms.
› what they are designed for. root canal access and exploration; tactile and magnification-enhanced endodontics; use by endodontists and general dentists.
› design aims they list. funnel-shaped access for file introduction, access to calcified and hidden canals, conserving peri-cervical dentin, and reduced dependence on ultrasonic tips.
› tip and shape. against conventional access burs, ss white describe the micro-diameter tip as leading to more conservative access and the conical shape to more efficient access. they describe the tip as a self-centring guide, and the straight-line pathway as reducing the risk of gouging and perforation when used with an incisal access technique for canal entry.
“this is an ideal bur series for magnification-driven endodontics.”
eric herbranson, bs, dds, ms – quoted in ss white’s endoguide® brochure
ss white add a note to the kit listings: initial access and de-roofing in molars should be performed with either the great white® #2 bur or the great white® z diamonds supplied in the endoguide® anterior/bicuspid kit, order number 18052.
| single burs (5) | eg1a · eg1 · eg2 · eg3 |
| kits | endoguide® molar kit |
| hand file | vdw c-pilot™ 08, 25 mm · c-pilot™ 10, 25 mm |
| irrigants | chlorax 5.25% sodium hypochlorite · chlorax 2% |
endoguide® anterior/bicuspid kit · order number 18052 · eg1a, eg1, eg2, eg3, great white® gw2, gwz 856-018, gwz 801-018 · made by ss white burs, inc., lakewood, new jersey, usa · ref ssw-18052
triniti® initial file 22/.11 · 19 mm · 6 files
orifice openingcoronal flaringcrown-downrotary nitisterile, single use
an 11% taper on a 19 mm shank with a 9 mm active part – an orifice opener, not a shaping file. vdw's own description is that it replaces 2 or 3 gates enlargers.
| 11% taper | 19 mm overall length | 9 mm active part |
this pack: triniti® initial file, iso 22 tip, .11 taper, 19 mm, 9 mm active working part (pack of 6) · sterile, single use
ref v201357019000 · made by maillefer instruments holding sàrl, ballaigues, switzerland
› 19 mm overall, with a 9 mm active working part – an orifice and coronal-third instrument. it is not a file you take to working length, and the length is the reason
› 11% taper, iso 22 tip – vdw's figures for the instrument
› replaces 2 or 3 gates enlargers, in vdw's own words, with the depth of the flare bounded by the instrument rather than by feel
› three cutting edges on a convex triangular section – vdw describe the geometry as the efficiency of traditional k-type cutting blades, i.e. a convex cross-section to stabilise the instrument core and a cutting blade angle suitable for rotary use
› cut to clear debris – vdw credit the special k-type cutting edges with efficient removal of debris and dentine chips
› continuous rotation at approximately 300 rpm, with the torque set to the figure for the size – 140 gcm for this one
› supplied sterile and single use – ready to use, with no sterilisation before the case and nothing to re-process after it
read the 19 mm first, because it is the whole point of the instrument. this is a short, stiff, steeply tapered file for the orifice and the straight coronal third, and it is not built to be taken to working length in anything. crown-down begins there, and the traditional way to get there is a graded run of gates-glidden burs – three instruments, three changes, three chances to gouge a furcal wall with a bur that cuts on its side all the way round. one tapered niti instrument with a defined 9 mm cutting length does the same job with one change and a known depth. at 140 gcm – 1.4 ncm it carries the highest torque figure in the range, which is what an 11% taper needs.
the goal of root canal preparation is to create optimal conditions for a tightly sealed and long-lasting root filling, which includes a uniformly tapered canal shape.
vdw, on the triniti® range
it is a crown-down system, and this is where crown-down starts. vdw offer three sequences so that the run of files is chosen for the canal in front of you rather than applied to every case alike, but all three begin the same way: open the orifice and the straight coronal third first, then work apically with progressively smaller tapers.
triniti® came to the uk market in the early 2000s with one job: to get general practice to try niti – to move from stainless steel hand files to rotary nickel-titanium for the first time. the name carries that invitation and two further readings with it. the section is a convex triangle, so the blade cuts on three edges. and the instrument is nickel-titanium. try niti, tri, niti – three readings, one name, and it has outlived the campaign that coined it.
| rotation | continuous, approximately 300 rpm (vdw give a 250–350 rpm range) |
| torque | 140 gcm – 1.4 ncm for this file |
| handpiece | a torque-controlled endodontic motor with a reduction contra-angle |
| use | single use – a fresh file, then discard |
any torque-limited endodontic motor that can be set to a rotation speed and a torque ceiling will run it. we stock the x-smart® pro+ and the vdw.silver® reciproc, both with a 6:1 contra-angle.
| iso tip size | 22 (0.22 mm) |
| taper | .11, constant (11%) |
| length | 19 mm |
| active working part | 9 mm |
| material | nickel-titanium, rotary |
| motion | continuous rotation |
| supplied | sterile, single use |
| pack | blister of 6 instruments |
| manufacturer | maillefer instruments holding sàrl, ballaigues, switzerland |
| ref | v201357019000 |
what torque and speed should i set?
vdw's figure for this file is 140 gcm, which is 1.4 ncm, at a constant rotation of about 300 rpm. the torque is per file, not per range – every size in the range has its own number.
are they sterile, and can i re-use them?
they are supplied sterile and are single use in the uk. nothing to autoclave before the case and nothing to re-process after it, so there is no count to keep and no wear to judge – a fresh file every time, which is the whole argument for buying a rotary instrument sterile.
where does it stop?
the active part is 9 mm of the 19 mm shank, so the flare it cuts is bounded by the instrument rather than by judgement. vdw position it as the replacement for two or three gates enlargers at the orifice and in the straight coronal third.
what follows it?
the shaping files. the 20/.06, 25/.06 and 30/.06 carry the larger taper through the straight part of the canal; the .04 files take over where it curves.
| step | what we stock |
|---|---|
| patency | vdw c-pilot® 08 and c-pilot® 10 in 21 mm, or 08 and 10 in 25 mm – chosen by the canal, not by this file |
| lubricant | glyde™ file prep · file-eze™ |
| irrigants | chlorax 5.25% · chlorax 2% · endo-solution 17% edta |
| delivery | irriflex® 30g · navitip™ 29 ga |
| activation | vdw eddy® tips – vdw's own |
| shape | triniti® .06 and triniti® .04 files follow it |
| seal, resin | vdw 2seal® – vdw's own epoxy · ah plus®, the epoxy sealer every other one is measured against |
| seal, bioceramic | neosealer® ezflo – premixed, with 29 ga navitip cannulas; 25 mm tips, or 21 mm tips, matched to the canal |
| coronal seal | sdr® flow+ refill universal – 4 mm bulk increment, one cure |
resin or bioceramic is a real choice of technique rather than a ranking – we carry both because both are right in different hands. irrigation is the half of the case a file does not do: a crown-down sequence shortens the mechanical part, not the chemical one.
triniti® initial file 22/.11 · 19 mm · 9 mm active part · nickel-titanium, continuous rotation · 1.4 ncm at ~300 rpm · sterile, single use · blister of 6 · made by maillefer, ballaigues · ref v201357019000