VDW® C-PILOT® ISO 008 · 25 mm · 6 sterile files
Ten minutes into a lower molar and the 010 is going nowhere? That is the ordinary experience of a sclerosed canal, and it is not a reason to open the access wider. ISO 008 is a fifth thinner at the tip than 010, which is often the whole difference between an instrument that stops at a constriction and one that slips past it. C-PILOT® 008 is built for exactly that moment: stainless steel, thermally hardened for bending strength, with an inactive pilot tip that is guided by the canal rather than by force.
| 0.08 mm TIP DIAMETER | 25 mm WORKING LENGTH | 6 STERILE BLISTER |
This pack: 6 × VDW®STERILE C-PILOT® ISO 008, 25 mm, .02 taper · pre-mounted silicone stoppers · mfr code 368 025 008
Made by VDW GmbH, Munich, Germany
Read the instructions for most reciprocating systems and you will find a small hand instrument written into the sequence: check patency, and if the shaping file does not advance, create a glide path first. ISO 008 and ISO 010 are the sizes named for that job. Buying six of them is not an accessory purchase – it is the step that protects the far more expensive nickel-titanium file that follows, and the tooth it is working in.
At 0.08 mm the wire is very fine, so what it is made of decides how it behaves. VDW credit a special thermal hardening process with the file's high bending strength, and a laboratory comparison of pathfinding instruments in Endodontology in 2021 found the stainless steel files, C-PILOT® included, more resistant to buckling than the carbon steel and nickel-titanium instruments tested (Gupta and colleagues, DOI 10.4103/endo.endo_126_20). A bench test is not a clinical result – but buckling is precisely what an 008 does when the canal says no.
| 0.08 mm tip | A fifth finer than an 010 at D0 – usually the step that finds a canal an 010 has been sitting on top of |
| Inactive pilot tip | VDW's description: conducts the instrument safely along the canal, which is what keeps a fine file out of a false path |
| Thermally hardened | VDW attribute the high bending strength of the range to a special thermal hardening process |
| Radiopaque marks | Calibration rings and a radiopaque stopper – useful when the file is too fine to see clearly on a film |
| Sterile, ready to use | Gamma sterilised to DIN EN ISO 11137, blister of six, no cycle before first use |
| Constant .02 taper | The ISO hand file geometry – the blade widens by 0.02 mm for every millimetre back from the tip, so the size you read is the size the canal gets |
For probing in calcified root canals.
— VDW's stated indication for the C-PILOT® range. It is a scouting instrument, not a shaping one.
› Short amplitude – watch-wind in small arcs with the lightest apical load that still advances the file. Force at 008 buys a ledge, not depth.
› Pre-curve for a curve you can see – a slight bend at the last few millimetres helps the tip find the direction the canal is already going.
› Keep the flutes clear – irrigate and recapitulate rather than asking a lubricant to do it. Where a chelating gel is part of your protocol, File-Eze™ is the 19% EDTA option.
› Then hand over – once 008 is loose to length, move to 010 and only then to a mechanical glider.
Should I stock 008 or 006 as my rescue size?
008 first: it is the one you will use every week, and it is stiff enough to transmit a usable signal. Keep a blister of 006 behind it for the genuinely sclerosed cases, where 008 stops as well.
Can I autoclave and re-use them?
No. They arrive gamma sterilised in a single blister and VDW recommend single use of their pre-sterilised instruments. Since April 2007 the UK position has been that endodontic reamers and files are treated as single use and disposed of after each patient (CMO(2007)5, following the SEAC statement of 2006).
Six files for one canal – is that not a lot?
You will use more than one on a difficult canal, and a fine file that has been stressed is not one to re-introduce. Six is the sensible unit for a single sclerosed molar, not for six teeth.
| Finer still | C-PILOT 006, 25 mm · for sclerosed canals |
| Next size up | C-PILOT 010, 25 mm · the glide path reference size |
| Whole sequence | C-PILOT assorted 25 mm · two each of 006, 008, 010 |
| Lubricant, optional | File-Eze™ kit · 19% EDTA gel, if you use one |
| Mechanical glide path | WaveOne® Gold Glider 25 mm |
| Narrow anatomy | RECIPROC® Minima R20 25 mm |
| Then shape | RECIPROC® blue R25 25 mm |
| Shorter access | C-PILOT 008 in 21 mm · posterior teeth, limited opening |
VDW® C-PILOT® ISO 008 · 25 mm · .02 taper · calcified canals · patency · canal scouting · glide path · stainless steel · sterile · single use · 6 files · VDW GmbH · REF V040368025008 · also in 21 mm and 19 mm
SpotlightRECIPROC® MinimaOne file · slim shaping for narrow canals
Shaping systems
Hand files & finders
Materials & more